Product ID:METACERAM 21031
MSDS Date:07/14/1998
FSC:3439
NIIN:01-191-5053
Status Code:A
MSDS Number: CLRNJ

EUTECTIC CORP

9625-J SOUTHERN PINE BLVD
CHARLOTTE, NC 28273
US

Emergency Phone: 800-221-1433

Info Phone: 704-527-9800/ 800-221-1433

Cage: 72271

EUTECTIC CORP

CHARLOTTE, NC 28273 US

Telephone: 704-527-9800/ 800-221-1433

Cage: 72271

CHROMIUM

CAS: 7440-47-3

RTECS: GB4200000

OSHA PEL 1 MG/M3

ACGIH TLV: 0.01 MG/M3

EPA Report Quantity: 1 LB

DOT Report Quantity: 1 LB

ALUMINIUM

CAS: 7429-90-5

RTECS: BD0330000

OSHA PEL 5 MG/M3

ACGIH TLV: 5 MG/M3

NICKEL

CAS: 7440-02-0

RTECS: QR5950000

OSHA PEL 1 MG/M3

ACGIH TLV: 0.2 MG/M3

EPA Report Quantity: 100 LBS

DOT Report Quantity: 100 LBS

IRON

CAS: 7439-89-6

RTECS: NO4565500

OSHA PEL 10 MG/M3

ACGIH TLV: 5 MG/M3

MOLYBDENUM

CAS: 7439-98-7

RTECS: QA4680000

OSHA PEL 15 MG/M3

ACGIH TLV: 10 MG/M3

Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:YES IARC:YES OSHA:YES
Health Hazards Acute and Chronic:PRIMARY ROUTE OF ENTRY OF WELDING
FUMES, GASES, AND DUST IS BY INHALATION, SKIN, EYE CONTACT AND
INGESTION MAY ALSO OCCUR WITH POWDERS, PASTES AND LIQUIDS.
INHALATION: THE FUMES ASSOCIATED WITH HEATIN G, WELDING, BRAZING,
SOLDERING OR CUTTING METALS CAN BE DANGEROUS TO YOUR HEALTH AND
OVEREXPOSURE CAN CAUSE LUNG DAMAGE AND/OR OTHER ORGAN DAMAGE. USE
ADEQUATE VENTILATION TO KEEP BELOW EXPOSURE LIMIT S. KEEP FUMES AND
GASES FROM BREATHING ZONE. KEEP THE WELDERS HEAD OUT OF FUMES.
EYE/SKIN CONTACT: ARC RAYS AND ULTRAVIOLET LIGHT CAN INJURE EYES
AND BURN SKIN. LIQUIDS USED IN FLUXES/CHEMICAL AIDS M AY CAUSE
IRRITATION OR CHEMICAL BURNS.
Explanation of Carcinogenicity:THIS INGREDIENT IS LISTED AS A TOXIC
CHEMICAL IN SUBPART D (40CFR372), SUBJECT TO THE REPORTING
REQUIREMENTS OF SECTION 313 OF THE EMERGENCY PLANNING AND COMMUNITY
RIGHT-TO-KNOW ACT OF 1986. THIS INGR EDIENT IS LISTED AS A
CARCINOGEN OR POSSIBLE CARCINOGEN BY THE NTP, IARC OR OSHA 29 CFR
1910 (Z).
Effects of Overexposure:WARNING! POTENTIAL HEALTH EFFECTS OF PRODUCT
LISTED, AND WHEN USED IN ASSOCIATION WITH WELDING, BRAZING,
SOLDERING, THERMAL SPRAYING, OR PART PREPARATION ARE LISTED IN
HEALTH HAZARD SECTION. NO HAZA RDS EXIST FOR ARC WELDING
ELECTRODES AND BRAZING RODS BEFORE THEY ARE USED IN THE WELDING
PROCESS.
Medical Cond Aggravated by Exposure:AGGRAVATION OF PREEXISTING
RESPIRATORY OR ALLERGIC CONDITIONS MAY OCCUR IN SOME WORKERS.

First Aid:IINHALTION: MOVE VICTIM TO FRESH AIR SOURCE. CONTACT
PHYSICIAN AND ADVISE ON INGREDIENTS. SKIN: THOROUGHLY WASH HANDS OR
AFFECTED AREAS WITH SOAP AND WATER TO REMOVE ALL RESIDUE. IF RASH
OR BURN DEVE LOPS, CONSULT PHYSICIAN. EYE: THOROUGHLY FLUSH EYES
WITH WATER FOR AT LEAST 15 MINUTES TO REMOVE ALL RESIDUE. OBTAIN
PROMPT MEDICAL ADVICE FOR FLUXES AND CHEMICAL AIDS. ADVISE
PHYSICIAN OF INGREDIEN TS. INGESTION: CALL PHYSICIAN AND/OR LOCAL
POISON CONTROL CENTER. ADVISE OF INGREDIENTS.

Flash Point:NONFLAMMABLE
Extinguishing Media:CO2, DRY CHEMICAL FOAM TYPE.
Fire Fighting Procedures:TOXIC FUMES MAY BE PRODUCED- USE AN APPROVED
SELF CONTAINED BREATHING APPARATUS. THERMAL SPRAY POWDERS:
NONFLAMMABLE UNDER NORMAL WORKING CONDITIONS.
Unusual Fire/Explosion Hazard:SOME FLUXES AND CHEMICAL AIDS MAY GIVE
OFF HYDROGEN CHLORIDE, PHOSGENE AND CHLORINE GASES. CANS, UNDER
PRESSURE AND FLAMMABLES MAY EXPLODE.

Spill Release Procedures:IF A FLUX OR CHEMICAL AID IS ACCIDENTALLY
SPILLED, CONTAIN SPILL ABSORB AND SWEEP UP. FLUSH AREA WITH WATER
TO AN APPROVED CHEMICAL DRAIN.

Other Precautions:TRAIN WELDER TO KEEP HIS/HER FACE AWAY FROM THE
FUME/DUST PLUME. TRAIN WORKERS NOT TO TOUCH LIVE ELECTRICAL PARTS
AND TO INSULATE THEMSELVES FROM WORK AND ELECTRICAL GROUND.

Respiratory Protection:IF THE WORK STATION IS NOT PROPERLY VENTILATED
TO EXHAUST ALL FUMES, VAPORS AND DUSTS BELOW THE RECOMMENDED
EXPOSURE LIMITS, USE A NIOSH APPROVED RESPIRATOR.
Ventilation:USE ENOUGH GENERAL VENTILATION AND LOCAL EXHAUST AT THE
WORK SITE TO KEEP ALL FUMES AND DUST FROM THE WORKERS BREATHING
ZONE AND THE GENERAL AREA.
Protective Gloves:WEAR CHEMICAL OR OIL IMPERVIOUS GLOVES.
Eye Protection:WEAR CHEMICAL TIGHT GOGGLES. DO NOT WEAR CONTACT LENSES.
Other Protective Equipment:WEAR FACE SHIELD WITH APPROPRIATE FILTER
LENS RECOMMENDED FOR THE SPECIFIC WELDING OPERATION. USE FULL
PROTECTIVE EQUIPMENT NORMALLY USED IN WELDING/BRAZING OPERATIONS
SO AS TO PREVENT SKIN CONTACT.
Supplemental Safety and Health
ABBREVIATION: N/A = NOT APPLICABLE. N/AV = NOT AVAILABLE. N/K =
UNKNOWN. N/P = NOT PROVIDED. N/R = NOT RELEVANT. N/D = NOT
DETERMINED. N/E = NOT ESTABLISHED.

HCC:N1
Appearance and Odor:SPRAY, POWDER.

Stability Indicator/Materials to Avoid:YES
Hazardous Decomposition Products:FUMES MAY INCLUDE: COMPLEX OXIDES OF
THE METALS LISTED IN INGREDIENTS; THE FLUX COATINGS MAY PRODUCE
FLUORIDE COMPOUNDS, METAL OXIDES, CARBON & SILICA. "SEE OTHER
INFORMATION"

Waste Disposal Methods:DISPOSE OF IN AN ENVIRONMENTALLY SENSITIVE
MANNER IN ACCORDANCE WITH FEDERAL, STATE, AND LOCAL REGULATIONS.
USE APPROPRIATE MEASURES TO KEEP AIRBORNE DUST LEVELS CONTAINED IN
ACCORDANCE WITH EXPOSURE LEVELS OF SECTION 2. SEE ALSO SECTION 8
FOR PROPER SAFE HANDLING AND STORAGE.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.

SARA Title III Information:THIS INGREDIENT IS LISTED AS A TOXIC
CHEMICAL IN SUBJECT IN SUBPART D (40CFR372), SUBJECT TO THE
REPORTING REQUIREMENTS OF SECTION 313 OF THE EMERGENCY PLANNING AND
COMMUNITY RIGHT-TO-KNOW ACT OF 1986 : CHROMIUM, NICKEL, ALUMINUM.
State Regulatory Information:WARNING: THIS PRODUCT CONTAINS A CHEMICAL
KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER: CHROMIUM, NICKEL.